110 Ton C Frame Single Point Crank Precision Press

(Mechanical Feeding Shaft Is Reserved At The Front End)

1 Equipment model, name and quantity：

Equipment model	Name	Quantity	Note
ST-110	C frame single point crank precision press	1	Mechanical feed shaft is reserved at the front of the press

2 Energy and environmental requirements

⑴ Power supply voltage: 380V±10%, three-phase five-wire

⑵ Air pressure: pressure 0.6 ~ 0.8mpa

⑶ Operating temperature: -10℃ ~ 50℃

⑷ Working humidity: ≤ 85%

3 Equipment implementation standard

⑴ GB/T 10924-2009 《Accuracy of straight side mechanical press》

⑵ GB/T5226.1-2002 《General technical requirements for industrial machinery and electrical equipment》

⑶ GB5226.1—2002 《Mechanical safety mechanical electrical equipment - part I general technical conditions》

⑷ JB/T1829—1997 《General technical conditions of forging press》

⑸ GB17120-1997 《Safety and technical conditions of forging machinery》

⑹ JB/T9964—1999 《Technical requirements of straight side mechanical press》

⑺ JB/T8609-1997 《Welding technical conditions of forging press》

3.1 The equipment is in accordance with Japanese JIS level 1 precision inspection standard:

Precision items	Japan JIS 1 class
Flatness - Permissible Value around the Lower workbench（mm）

Parallelism - permissible value between the bottom surface of the slider and the lower workbench（mm）

Verticality of the slider up and down with the lower workbench surface - permissible value（mm）

Verticality - permissible value of die shank hole to slider bottom surface（mm）

Total clearance - permissible value of upper and lower operating mechanism（mm）

4 Main equipment parameters

Number	Item	Unit	ST-110(V)
1	Transmission type	——	Crankshaft,
2	Body type	——	Integral steel plate welding
3	Nominal capacity	Kn/Ton	1100/110
4	Slide guide bit structure	---	Two points and six paths
5	Ability point	mm	6
6	Applying points	point	1
7	Slider travel length	mm	180
8	Maximum modulus height	mm	360
9	Slider adjustment	mm	80
10	Continuous trips per minute	Times/Min	30-60
11	Size of upper workbench (left and right x before and after)	mm	910 x 470
12	Size of lower workbench (left and right x before and after)	mm	1150 x 600
13	Main motor power + frequency converter	kW x P	11 x 4 + Frequency converter
14	Air source pressure	MPa	0.6
15	The color of the press	color	White
16	Precision grade	Grade	Japan JIS level 1

5. Technical requirements

5.1 Main structural features and methods

(1) High frequency quenching treatment of slide guide rail, hardness above hrc45,

Advantages: greatly improved wear resistance. (other manufacturers do not have high frequency quenching treatment)

(2) The surface roughness of the slider and guide rail is as high as ra0.4-ra0.8,

Advantages: high precision and low wear. (no quenching and grinding treatment from other manufacturers)

(3) The flatness of slide guide rail is 0.01mm/m, and the precision is high.

Advantages: the accuracy is greatly improved. (other manufacturers above 0.03mm/m)

(4) All our air circuit components are SMC Japan. (other manufacturers generally use domestic products).

(5) We adopt American MAC brand for air spraying solenoid valve, which has high sensitivity of air spraying reaction.

(6) The crankshaft made of 42crda is the best in China

Advantages: the strength is 30% higher than that of 45 steel, and the service life is longer. (other manufacturers generally use 45 steel)

(7) The copper sleeve is made of zqsn10-1 (Tin Phosphorus Bronze) (similar to Aida copper sleeve). Other manufacturers adopt bc6 (high strength brass, also known as 663 copper), has 50% higher strength (surface pressure) than ordinary copper, and is more wear-resistant and durable, Longer precision and longer service life.

(8) All our piping is Φ 6, and the oil circuit is smooth and not easy to be blocked. (other manufacturers usually use Φ 4)

(9) The ball seat adopts Japanese TM-3 sintered copper alloy (same material as Aida)

Advantages: the probability of biting is greatly reduced (general manufacturers are cast iron).

◆ Environmental impact

This product has no adverse effect on the environment and will not produce harmful gas.

◆ Handling and installation

⑴ Transport and storage of equipment:

① The equipment adopts appropriate anti-rust, anti-vibration and anti-impact measures in the packaging process, which can guarantee the transportation and storage of 5°c ~ 45 °c.

② When the equipment is transported and stored, attention should be paid to it. The equipment and outer packing should not be directly exposed to rain or water, and the outer packing should not be damaged.

⑵ Lifting of equipment:

When lifting and unloading by crane, the bottom or side of the product shall not be subjected to shock or strong vibration.

⑶ The installation:

Remove and clean the plastic film wrapped on the outside, remove the plug, and install PU1 pipe connector and PU pipe, the length of PU pipe is about 700mm.

5.2 Main component structure

⑴ Mechanical parts

The frame is welded with Q235B material. After welding, tempering is carried out to eliminate the internal stress of the material. Fuselage guide rail position with two corners of six guide road.

⑵ Transmission type

The transmission gear, crankshaft and connecting rod are assembled on the upper part of the press. The main motor is installed on the rear measuring surface of the frame, flywheel, clutch, etc

In the position of the rear side of the frame, the flywheel has been tested for balance before assembly.

The gear part adopts straight tooth transmission mechanism, and its material is made of high-strength alloy steel 42CrMo, and the corresponding heat treatment is carried out.

Dry low inertia clutch/brake. The clutch/brake control system is equipped with an abnormal detection device.

All shafts receiving are made of tin-phosphorous bronze wear-resistant material.

⑶ The slider

The slider is made of HT250 material. The guide adopts two-point six-side rectangular guide,

The bottom surface of the slide block and the top surface of the table have T-groove, which is used to install the mould. The height of sliding block is adjusted by electric motor over 80 tons (including).

Adopt hydraulic automatic overload protection system.

⑷Lubrication system

The press is lubricated with electric butter and equipped with low oil level alarm system, so it is safe and reliable. The equalizer is: manual butter feeding pump.

⑸ Balancing device system

Adopt air pressure type slide block balance device, Air pressure can be controlled at the air pressure regulating valve.

⑹ Electrical part

The electrical equipment is controlled by PLC, equipped with powerful human-machine interface, and displayed by the touch screen of famous brands.

Placed on the main operation panel, the following functions can be achieved:

①The touch screen displays Chinese characters (or switch between Chinese and English), which is simple and easy to understand, and displays various data parameters of the press, such as the number of strokes, electronic CAM Angle, etc.And the corresponding data can be set through the touch screen;

② Display the working flow of the press, so that the operator can operate the press more easily，and has the main flow state indication；

③ Operation and failure information display, so that operators and maintainers more quickly to solve the press problems, reduce the downtime;

④ PLC input/output point real-time monitoring function;

⑤ Set the product count screen, which can display the current product count in real time, and set the target number of work pieces.

⑥ Electric control press adopts three-phase power supply, 380V,50Hz.

⑦ The main motor is equipped with thermal overload and zero speed anti-reversal protection.

⑧ The realization of each function of punch control has corresponding safety chain. The panel is equipped with fault indicator light and reset button to complete the function of reset after fault confirmation.

5.3 Mode of operation

Press set inching, single, continuous three operating modes. The working mode is selected by the switch and centrally controlled by the button.

5.4 Safety measures

⑴ Emergency stop button: press "emergency stop" button in case of abnormal operation of press. The press has three emergency stop buttons.

One on the operation control panel, one on the column, one on the two-handed operation table; Press any of the emergency stop buttons and the press will stop immediately. The position of the emergency stop button on the column is about 1.2 meters from the ground, which meets the requirements of ergonomics；

⑵ Two-hand operation button: two-hand downward synchronization time limit is 0.2-0.5s;

⑶ Overload protection: the slide block is equipped with hydraulic overload protection system to ensure that the press will not damage the press and die due to overload.

Overload after the slider that stays at the bottom dead point, can only use inching, reverse return to the top dead point for readjustment and pressure, work.

6. Configuration of equipment

6.1 Main structural part

Serial number	Part Name	model	Materials, treatment methods
1	Machine frame	Basic piece	Materials Q235B
2	Workbench	Basic piece	Materials Q235B
3	Crankshaft	Basic piece	Materials 42CrMo, quenched and tempered Hs42±2⁰
4	flywheel	Basic piece	Materials HT-250
5	Slider	Basic piece	Materials HT-250
6	Cylinder	Basic piece	Materials 45
7	Worm gear	Basic piece	Materials ZQSn10-1 Tin phosphor bronze
8	Worm	Basic piece	Materials 40Cr, quenched and tempered Hs40±2⁰
9	link	Basic piece	Materials QT-500 Blunting treatment
10	Sawtooth ball head	Basic piece	Materials 40Cr, quenched and tempered Hs40±2⁰
11	Slider guide	Basic piece	Materials HT-250, High frequency quenching hrc45 degrees above
12	Copper (copper sleeve)	Basic piece	Materials ZQSn10-1 Tin phosphor bronze

6.2 Main parts manufacturer/brand

Nunber	Part Name	Manufacturer/brand
1	Main motor	Siemens
2	Slider adjustment motor	SANMEN
3	PLC	Japan Omron
4	AC contactor	France Schneider
5	Intermediate relay	Japan Omron
6	Dry clutch brake	Italy OMPI
7	Double solenoid valve	USA ROSS
8	Thermal relay, auxiliary connector	France Schneider
9	control button	France Schneider
10	Air filtration	Japan SMC
11	Oil mister	Japan SMC
12	Pressure reducing valve	Japan SMC
13	Hydraulic overload pump	Japan，Showa
14	Two-hand button	Japan Fuji
15	Electric oil pump	Japan IHI
16	Main bearing	USA Timken /TWB
17	Anti-vibration foot	Hengrun
18	air switch	France Schneider
19	Frequency converter	ZHENGXIAN
20	touch screen	Kunlun Tongtai
21	Seals	Taiwan SOG
22	Preset counter	Japan Omron
23	Multi-section switch	Siemens, Germany
24	Air blowing device	USA MAC
25	Mold die illumination	Puju LED
26	Misfeed detection interface reserved	Wiring through PLC
27	Photoelectric protection device	LAIEN

6.3 Accessories, special tools list

Number	item name	Type of goods	Quantity	Optional / standard
1	Maintenance tools and toolbox	accessories	1 set	standard

6.4 Special equipment (for options) list

Number	name	Brand	Optional / standard
1	2-channel tonnage	Japan Rikenji	Optional
2	Misfeed detection device	Japan Rikenji	Optional
3	Bottom dead point detection device	Japan Rikenji	Optional
4	Rapid mold changing device	Taiwan Fuwei	Optional
5	Feeder machine	Taiwan TUOCHENG	Optional
6	Die pad (air cushion)	self made	Optional
7	Feeding group	self made	Optional

ST-series Machine Technical Description