Top Suppliers 25t Open Type Single Crank Press Machine - Pull Down High Speed Press (HX series) – Daya
Top Suppliers 25t Open Type Single Crank Press Machine - Pull Down High Speed Press (HX series) – Daya Detail:
DAYA straight side double crank punch press
VS
Other straight side double crank presses
Daya press
Daya press: with platform and safety fence, convenient for clutch maintenance and change of cooling oil, main motor belt is loose and easy to adjust, and convenient for subsequent maintenance. Safer and more convenient.
Other press
Other press: Without maintenance platform. Clutch maintenance, replacement of cooling oil, loose adjustment of main motor belt, etc. which can only be completed with the assistance of forklift, which is not convenient for subsequent repair and maintenance. There are some potential safety hazards.
Daya press
Daya press: Daya press adopts four corners and eight sides to surround the guide rail. In the stamping forming position, the slide guide rail is included by all the guide rails on the table body. This kind of guide rail has the characteristics of high stamping accuracy, strong anti eccentric load capacity, small rail wear and long precision retention time.
Other press
Other press: the guide rail with semi enclosed structure as shown in the right figure is adopted. During the stamping process, there is a section of guide rail exposed. During the stamping process, the slide guide rail is easy to tilt, with poor anti bias load capacity, large rail wear, short precision retention time and high maintenance cost.
Daya press
Daya press: the distance between the two points of force application is more than 60%; Advantages: the larger the distance between the two force application points, the greater the eccentric bearing capacity; the larger the distance between the two force application points, the higher the design cost.
Other press
Other press: the distance between the two points is generally less than 50%; Disadvantages: the smaller the distance between the two force application points, the smaller the eccentric bearing capacity. The guide rail is easy to tilt, the guide way is easy to wear, and the precision of guide rail is poor.
Daya press
Daya press: forced thin oil circulation system, energy saving, can be recycled, fan thermal performance is good, compared with grease lubrication can be increased by 5-10 beats per minute.
Other press
Other press: electric grease pump, grease can not be reused, no advantage of forced thin oil circulation system.
Daya press
Daya press: when the stroke length is the same, the forced thin oil circulation system has higher efficiency, compared with grease lubrication, it can increase 5-10 beats per minute. Strictly follow the Japanese JIS level 1 standard; the Japanese JIS level 1 standard is higher than the Taiwan CNS level 1 standard.
Other press
Other press:electric grease pump, grease can not be reused, no forced oil circulation system advantages. according to Taiwan CNS level 1 standard
Slide guide of Daya punch press
VS
other slide guides of punch
Daya press
Other press
Guide rail of Daya punch press
1.High frequency quenching process: hardness above hrc48;
2. Grinding process of guide rail: the surface finish can reach ra0.4-ra0.8 (mirror surface), flatness, parallelism and verticality within 0.005mm/ ㎡.
3.The machine tool has the advantages of small wear, high precision, long precision maintenance time, long service life and low energy consumption.
Other press guide railno quenching process; milling processing, surface roughness ra1.6-ra3.2, flatness, parallelism, perpendicularity more than 0.3mm / ㎡
Daya press crankshaft
VS
other press crankshafts
Daya punch press: the crankshaft is made of high strength alloy 42CrMo Advantages: the strength is 1.3 times higher than that of 45 steel, the service life is long, the wear resistance is good, the wear is small, and the precision is maintained for a long time.
Other presses: made of 45 steel, Disadvantages: low cost，the strength and wear resistance are not comparable to 42CrMo
Daya
Oil way of DAYA punch PRESS: Φ 8 is used for oil pressure lubrication piping.
Advantages: long pipeline, large diameter is not easy to block, break, ensure the safety of lubricating oil, smooth.
Other
Other presses: the oil pressure lubrication piping of press adopts Φ 6.
Product detail pictures:
Related Product Guide:
We have been proud from the higher consumer gratification and wide acceptance due to our persistent pursuit of high quality both on product or service and service for Top Suppliers 25t Open Type Single Crank Press Machine - Pull Down High Speed Press (HX series) – Daya , The product will supply to all over the world, such as: Austria, Bulgaria, Afghanistan, We taking advantage of experience workmanship, scientific administration and advanced equipment, ensure the product quality of production, we not only win the customers' faith, but also build up our brand. Today, our team is committed to innovation, and enlightenment and fusion with constant practice and outstanding wisdom and philosophy, we cater to the market demand for high-end products, to do professional products.
By ROGER Rivkin from Zimbabwe - 2017.08.18 11:04
Adhering to the business principle of mutual benefits, we have a happy and successful transaction, we think we will be the best business partner.
By Josephine from Indonesia - 2017.09.29 11:19
Products categories
-
Good quality 35t Punch Machine - Frequency Con...
-
Cheapest Price Hydraulic Press Supplier - Stra...
-
Best Price for Turret Punch Press - C Frame Hi...
-
Best Price on Four Axis Articulated Robot - Fo...
-
18 Years Factory 65t Gantry High Speed Press Ma...
-
China Manufacturer for Air Compressor Tube Fact...